Sunday, January 6, 2013

Rear Suspension Knuckles

The rear suspension of the Classic Revival round-tube chassis is based on the VE Commodore rear. In fact, it is the same as the VE rear with the following changes;
  • Driveshafts are shortened by 65mm each side
  • The top suspension A-arm is custom made
  • There is no rear K-frame, with all arms and components having mounts built-in to the chassis design
All the components I am using for the suspension are either brand new where there are moving parts (eg bearings), or stripped and fully-rebuilt/painted where it is a static component (such as a simple steel suspension arm). I will make a video shortly of assembling the rear-end, but first this post explains the rebuild of the rear suspension knuckle. I thought this was worthy of its own blog post because there are so many parts to the knuckle. After the knuckle was stripped bare, blasted and painted, assembly can begin;

Clockwise from the bottom left corner we have;
  • Main drive-flange
  • Handbrake backing plate and retaining bolts (backing plate has been trimmed as per this blog post)
  • Handbrake shoe and retaining spring
  • Main driveshaft bearing and retaining circlip
  • Top A-arm heim joint
  • ABS sensor and retaining bolt
  • Handbrake adjustment and actuating mechanism components
  • Two polyurethane bushes and crush tubes



The first job is to press in the polyurethane bushes. The cast knuckle unit itself is extremely unwieldy and an awkward shape. It is difficult to fit in the press for some components and impossible for others. There are 5 pressing operations to be made, for which I used a combination of workshop press, vice, and socket/bolt methods. The main drive bearing and drive flange must be installed with a proper press.





Once the bush is in, it is greased up and the crush tube can be installed by hand with some force.



The top suspension A-arm mounts to a heim joint unit which is pressed into the top mounting of the knuckle. This is an awkward piece to install. I started it and seated the first 3mm with the socket/bolt method, and then this is one of the awkward press positions you need to use to drive it home.



Fully seated



Next up the main drive bearing has to be pressed in. The bearing has the ABS reluctor built-in to the inner race, so the bearing must be installed in the correct direction for the ABS sensor to work. Installing this bearing is fairly straight-forward in the press. To push it home the last few millimetres I took the old bearing housing, ground it down by a few thou on the grinder so it wouldn't get stuck, and used it between the press and the new bearing, this insured I was pushing square on the new bearing and only on the outer race (there is no picture of this step, sorry). The old bearing also served nicely as a spacer underneath while pressing.







Then the bearing retaining circlip is easily installed



View from the back, ABS side



Now the handbrake backing plate and actuation/adjustment mechanism can be greased, assembled, and installed. The dumb thing about this knuckle design is that once it is fully together the handbrake mechanism cannot be removed without removing the drive flange, an action which destroys the wheel bearing in the process. I guess GM thought they could make money out of selling wheel bearings as part of a handbrake rebuild!



The two retaining bolts for the actuator housing and the one top bolt on the backing plate all get thread-locker - once it is finished there is no way to tighten them! The top bolt is out of view in this photo, directly above the bearing housing just under the middle-top of the handbrake shoe.



Next the main drive flange is pressed into the bearing. It's important here to have a supporting socket or other suitably sized spacer underneath the knuckle, with the inner bearing race resting on the spacer underneath (I used a large 3/4" drive socket, size-wise it needs to be suporting the inner bearing race). This is because the bearing inner race is actually two pieces, one on each side, which are held in place by the drive flange. Failure to support it means pressing in the drive flange will sepaate the bearing. In the end the bearing is held together by the drive flange. With the lower race supported, pressing in the drive flange forces the bearing together.



Insert the ABS sensor, thread-lock the retaining bolt, and voila. Finished!



Repeat for the other side. I didn't time it, but I estimate that the first knuckle assembly took me at least 3 hours, the second one took 50 minutes :-)





1 comment:

  1. Thank you for some other informative blog. Where else could I get that type of information written in such an ideal means? I have a mission that I’m just now working on, and I have been at the look out for such information. Used Acura Parts

    ReplyDelete

Note: Only a member of this blog may post a comment.